Painted Stairs and Adding Runners

You’ve all watched as my stairs transformed before your very eyes and we ripped that old carpet off and added new pine stair treads and new risers as well.  I knew that I could make the stairs look pretty and had every intention of adding a runner, just like I did in my old house.  I loved how that one turned out so much and wanted to repeat the pretty again.

In came Dash and Albert runners with a blessing from Wayfair.com and I received the runners for my stairs from them as a gift.  Of course, they knew I’d be blogging about it and spreading the word, so it’s a win-win for both of us. 😉

prep stairs

Here are my main stairs after ripping off the nasty old carpet.  That was one of the first things I did.

painting stairs and runners

Here they are in progress and you can see the painted pine stair treads going on, as well as new white risers. painted stairs

You can see the entire tutorial on ripping up carpet and adding new stairs.  That totally updated the stairs and I would be really happy with painted stairs, but I definitely wanted to soften them up with runners.  I found these Dash and Albert runners (affiliate link) online at Wayfair.com and they are perfect for my renovation.  They are indoor/outdoor and should be very durable and clean up nicely.

Shurtape carpet tape

I knew that I’d be using an electric staple gun for this project, but had a lightbulb moment when I thought about getting some double sided carpet tape that I found at Lowes.  This is really pretty sticky and I thought it might help to keep my runner in place.

I decided to leave 5 inches on each side of my runner for the stairs to show.  I have 3 stairs in this house, the foyer being the widest.  On the foyer stairs, I left the runner intact, which is about 2.5 feet wide.  It was fine to leave a large expanse of wood showing on either side, so I used the full width of the runners.

On the other 2 stairs, though, they are different widths, so I visually looked and decided to leave 5 inches of painted stairs showing on either side of the runner.  That required me to get my other 2 runners cut down and bound on each side.  For the main stairs, I cut and bound them to 24″ and the other stairs going to the den, I cut and bound at 26″.

Does this make sense?  I wanted those 2 stairways to visually have 5″ of dark wood showing on either side, so that’s how I figured it out.  I took my runners to to a local place in Kennesaw, RBS,  that cuts and binds rugs and had them do it.  It cost me $60 to cut down all my runners and have them bound, which wasn’t bad at all.  They matched up the binding to what was on the ends of my runners and it all turned out great.   Hang on and you’ll see the finished stairs!

add tape to riser

So, to get started on putting these in, I added my double sided tape 5″ in from each side.  I added it to the back of the stairs, and to the very top of the first stair, outlining where I’d be putting the runner.

stair runner installed

I left the binding on the top of my runner and used it right against the base of the floor at the top step.  And I did add some staples to the top too, trying to hide them as best I could right at the edge of the binding and runner, as indicated by the arrows.  You really can’t see the staples unless you really get down and look for them.  Using the tape allowed me to use less staples.

adding carpet tape

You can see the part that I’ve already pulled off the backing, leaving a sticky strip to press the runner down on.  You’ll need scissors for this too.

adding runners to stairs

Once you get the very top stair in place, then it’s time to wrap the runner over the nose of the stair and staple.  I pulled it taut and then just pressed the stapler up under the stair nose, stapling underneath every 2 inches or so, creating a tight fit on the runner and stair.  I did this method with each and every stair until I reached the bottom.

adding runner to stairs stapling

Staple, add tape, and move on down.  Always start at the top and move down to the bottom, that’s what worked for me.  Then, at the bottom, you’ll cut off the excess runner.  On my longest stairs, I did have to piece this one together and I’ll show you how I did that too.  The other two just got trimmed off and the edges were tacked down.

cut under stair

So, I’ve moved all the way down as far as my runner will go on my longest stairs.  I wrapped it around the stair nose and then cut off the excess, stapling that all underneath.  You can see that these runners will ravel, that’s to be expected with a raw edge.  But, the new piece will cover that up.

One thing to be aware of.  Be sure and measure at least on one side as you are moving down the stairs to be sure you’re leaving the same amount of stairs showing all the way down. It’s easy to let the runner slide a little and that could throw off the runner an inch or more if you’re not careful.  Just throw a tape measure up every time you get to the next stair to be sure that the right amount of inches are showing on your stair.  You don’t want to get to the bottom and have it all wonky looking and out of line, do you?!

adding runner to stairs

Above is the extra little piece that I cut off this runner.  I had gone as far I could with the long runner and had one little piece left that I actually used too.  You will want to piece anything right under the stair nose and that will hide the staples and no one should ever know it was pieced if you do it well.

adding runner to stairs binding cleanup

Next, I took the extra piece that was going to finish these stairs off (I actually got 3 long runners and then had to get an extra 2×3 rug which finished out my  long stairs).  I got all of these bound at 24″, so it worked out fine for these stairs.  This piece was my extra 2×3 rug.

adding runner to stairs binding fix

Instead of cutting off that binding, I simply turned it under.  It will be stapled right under the stair and it’s about the 3rd stair up on my staircase, so no one will see that it’s been pieced even though that binding adds a little bit of thickness there.  With the double sided tape in place and stapling, I got it on nice and tight.

piece under stair

I moved on down the last two stairs until I got to the very bottom.  The rug just fit under the last stair without cutting any of the binding off.  I didn’t have enough to go down to the bottom of the riser, so I used the other small piece that I had cut off above.

place under stair and staple

I fit that piece on at the bottom and ran it right above my quarter round molding next to the stairs, leaving the binding intact.  Once I got that in place, I simply turned under the top of the rug to hide the raveling edge and then stapled/taped this little piece into place.

bottom stair runner install

And ta-da!  Done!  I’ve got all 3 stairs finished now and they look wonderful.  See can you tell where I’ve pieced the rugs?  You can’t, can you?  It’s barely noticeable and using tape and staples, the runners are on there pretty tight.  I don’t think I’ll have a lot of problem with them moving, but if they start to loosen up with wear, I’ll just add some more staples.

main stairs looking up

Here’s the longest staircase all finished from the bottom looking up.

main stairs new runner installed

And from the top looking down.

den stairs down

The den stairs got the exact same treatment.  This runner is so pretty and I think will be a good choice.  Very neutral.  You can see the binding that the rug company put on, it turned out really nice.

den stairs up runner binding

From the den looking up.

foyer stairs painted runner

And the foyer stairs with no binding.  Again, I left these as they were and didn’t need to cut them down since these stairs are extra wide coming in the front door.

foyer stairs up

I absolutely LOVE how they all turned out, exactly as I had it in my head all those months ago.

living room looking to stairs

I love that there are ways to make stairs look pretty these days without spending a fortune on hardwood stairs.  So glad I went this route and painted my stairs and added runners.  To me, they look so sophisticated and beautiful.

What do you think? 

Do you have some stairs that need a makeover? 

I did a very similar painted stairs with runner treatment in my old house and loved those too.  I expect that I’ll love this one even more!

Joining Traci’s party and Beth’s this month!

SaveSave

- Rhoda

Comments

  1. looks marvelous!

  2. I was hoping you would blog about the runners as I peaked at them in your Open House post! I absolutely love them. I, too, have a split entry so I am thinking that I COULD do this! Mr. Spouse sounds as if he is stomping going up and down the stairs!

    It is beautiful!

  3. I wish I had stairs – ugly or not!

    They look fabulous, Rhoda. 🙂

    I really enjoyed the Hometalk chat on Twitter last night. Thanks for your encouragement 😉

  4. Your house looks amazing! The before and after pictures are stunning. I just adore your style! 🙂

  5. Your skills have def improved with doing stuff, Rhoda! I went back and looked at your first go in your old house, and this time round everything looks v. professional. I think I may take this idea up for my own stairs, as we have side to side carpet currently, and after 10 years, I am yearning for a new one!

  6. I absolutely love how they turned out! I love the print on the rugs, so chic but still neutral

  7. Lovely! This is my top project on the list of “to do’s” this year. My basement is newly remodeled but the stairs are bare with contractor’s magic marker showing measurements and dimensions from when the house was built. I also want to stencil the cement floor so I have lots to tackle…thank you for posting, your home is so beautiful. I spent a lot of time on your blog last night getting ideas 🙂

  8. I LOVE this project! It looks great and so professional too. 🙂

  9. Oh wow… I love what you did to your stairs! This makes me wish I had stairs!

  10. Rhoda, this looks great! You have had so many amazing transformations in your home! Thanks for the awesome tutorial!

  11. Malinda Clay says

    These look AWESOME!
    Great job on the stairs and everything else in your beautiful home. It’s just wonderful. So proud for you.

  12. Fabulous!

  13. I love how you added the runners – they look awesome! Thanks for the tutorial — I definitely need to do this with the stairs to our basement!

  14. Mary in Idaho says

    Love your blog and enjoy all the beautiful creative things you are doing to your home. Hoping to begin receiving emails again reminding me of your new posts. They are a wonderful reminder to check out what you are up to! 🙂

  15. It is just gorgeous and brilliant! Never heard of carpet tape, might need to use that in our family room. I must have missed the fabulous front door, love the pop of color!
    XO
    Kristin

  16. Hummm……I’m not
    finding the pictures
    along with the text…….
    Is it just me????

  17. Rhoda those look so pretty i remember how your other stairs turned out and these are just as pretty.they are so sleek and pretty.My best friend and i would have loved to come to your open house but we live in the Little Rock area and was a little far for us. however i would have loved being there i know it was pretty. your stairs are so pretty i know you are enjoying them so much i would love to do this to my stairs . You have done such a pretty job on everything Rhoda it is very pretty!

  18. I absolutely love this. It looks fantastic. Great job on your part!
    xo Nancy
    Powellbrowerhome.com

  19. Rhoda, your stair project is beautiful. I have been reading your blog since discovering it this past fall, and love the creative ideas you implement so well. I have a practical problem with my stair risers, which I have been wanting to cover for several years and did not know what to use until reading your post. (Discovered poorly-stained-by-builder treads when we moved into house, but that’s another story.) Now that I know what and how to ‘cover the ugly,’ risers, I am dead serious when I ask: Does a small brad nailer require an air compressor? I would appreciate your answer–I know very little about tools and need to do these jobs myself. Thank you for sharing your projects. (BTW, I live in the neighboring state you left to begin your new life, and we hope to soon be about 100 miles south of where you are now.) I am trying to spiff up the present homestead so we can leave here later this year to be closer to our family. You have given your readers inspiration and courage.

    • Cissy, yes, you would need an air compressor for any nail gun. They are worth it if you’re doing many projects like this.

  20. Looks great! Thank you for sharing how you did them.

Speak Your Mind

*

This site uses Akismet to reduce spam. Learn how your comment data is processed.